Q. I am interviewing contractors to do renovations w/ electrical work. When selecting someone after a horror show from getting a contractor off creigs list ( don't recomend that ) I ran into a few who said they did not need an electrcians licence because its not a big job? I would apparecate the feed back.

A. Yes, electrical and plumbing contractors need to be licensed. That doesn't mean the person actually doing the work must be licensed, but the owner of the shop or the person in charge of the field personnel must be a licensed master electrician or plumber. Hope this helps.

(No Chosen Answer)

Q. My first contractor flaked out and never gave me an estimate after I spent hours explaining to the plumber and electrician what I wanted done. Now I am trying to get the plumber and electrician's estimates and have them lined up to work on a specific date. "Professional courtesy" because the bid was under the flakey contractor has impeded the process. I want to save the "surcharge" my contractor would charge and just hire the plumber and electrician by myself. Why is this so hard? What is the secret code to get this done??!! I want to save myself the money, especially since the bids are already done and they know what I want/need done!

A. Yes of course you can! But if they are the general contractors sub contractors they might not feel right about doing it without the contractor. If this is the case, go through your local phone book or a home improvement book (they usually have them for free in the super markets) and find a LICENSED and INSURED plumber and electrician.

(No Chosen Answer)

Q. Hello! My boyfriend and I are considering a new Chandelier for our dining room, the one that came with the place is quite old and not very chic. I have found one that I like and he has said that he might be able to do it, but I figure if an electrician's fee is not too steep, I would rather a professional do it. How much do you think replacing a chandelier should cost? Thank you!

A. Call a local electrician to get a price. Here in the US, I would have no idea what an electrician in Australia charges. The price will depend on whether you get an electrical contractor, or hire an electrician to do it "on the side". Hope this helps.

(No Chosen Answer)

Q. I Bought a building that has 3 phase service. What I would like to do is have a 200 amp single phase Breaker on on each Floor (there are 4 Floors total) These can be sub panels or otherwise. My question is how do hook up a Main Distribution panel to tap into the 3 phase panel and maintain a balanced load. I know this is a dangerous undertaking. I am very experienced in single phase applications But my 3 phase experiance so far has been limited so far to installation of 3 phase motors. In theory I somewhat understand what needs to be done, but I need someone to give me a step by step process to complete this. ** again I understand the risks involved so please do not answer telling me to Hire an Electrician...I am ONE. Just dont know too much about this aspect and Doing it by oneself is the best way to learn** Thx If necessary compensation can be arranged.

A. I am sorry, and mean no offense, as you have stated that you don't want to hear this, BUT... It would be foolish, and possibly hazardous, for anyone to try to explain this to you here. You "say" you "are one," but you also say you don't know about this, and that's the same as not being one where this project is concerned. You need to sacrifice a little pride and money, and hire a LICENSED MASTER Electrician to go to your job-site and literally POINT to, identify each of the phase legs, and explain which are to be used for your intended project. You don't have to hire him to do the work, only to advise and educate you. How about one of the guys you work with who does this work, he probably would do it for a few beers and laughs. There is a universal convention for which phase to use for what you want to do, and someone who knows what he/she is doing needs to precisely identify which phase line is which. The reason for this is that whoever originally wired the 3-phase may NOT have followed the convention, and misuse could result in problems. Better safe than sorry.

(No Chosen Answer)

Q. Last year I was about to do this install for my stereo, I bought all the stuff I need and then right when I was about to install it all, I took a reading of my power wire and it seemed to damn high already from what was coming from it. ( I can't remember the voltage because it was a year ago) I showed my uncle that's a mechanic ( not an electrician) and he said that "I wouldn't do it because it's already hi and it might fry lots of things" I know that the voltage was above 12.6 for sure! maybe 14 something? and that's before I even installed any extra gauge wire. so I just changed my mind and never installed it...I still have everything and I'm wanting to try this again and actually doit but I really don't want to ruin my car or fry all my audio equipment, should I hire a professional shop to do this so then they are liable for any damage? also - I have a kinetic 1400 battery under my hood powering my car. and my stereo is jl audio amp and sub. I don't want to buy a HO alt yet. thanks

A.

(No Chosen Answer)

Q. What do contractors charge per square foot to remodel part of an unfinshed existing basement to a bedroom? I am looking into converting part of my unfinsihed basement to a bedroom around 12ft x 12ft. There will be no Addition to the house, but there will be remodelling to already existing space putting up some walls to make a bedroom. Ballpark figure thanks.

A. Even a Ball Park figure would be difficult to produce for with out a visit. But lets say, the electrician could be about $1,000.00 total. X 15.15 divided by 144.

(No Chosen Answer)

Q. Do they charge as much as materials cost? More? Less? I want to refinish my basement. No plumbing. Just new walls. carpet, lighting, moulding, doors and windows. I figured all materials would be around $5-7k. What would he charge?

A. Depends on how much work there is to do and where in the US you live...you will have to get an electrician and permits for that. I would say it would cost twice as much as the materials. It really just depends on where you live and who you can find. Your best bet is to not look on yahoo answers and to call local contractors and they will give you free estimates.

(No Chosen Answer)

Q. I received a bid today for a partial basement remodel from an acquaintance of mine that I'm pretty confident I can trust. He quoted me $6,500 to complete 625 square feet. This includes dry wall, the ceilings, outlets, canned lighting, carpet, 3 doors and paint. Is this a pretty good price? Also, I have a home equity line of credit with 3.75% interest. I think I should use this because it's tax deductable. I can't pay cash and don't want to use a credit card. Well, I could pay half cash and half line of credit but I don't want to break myself paying for this all up front. Is the HELOC a good idea? Thanks. wow. Thanks for the detialed advice. Um, yes he is putting 2 x 4 studs in and blowing insulation in. The painting will be contracted out to a painter, the electrical to an electrician and the carpet to a local company. It sounds like the guy is in charge of the job but contracting most of it out. It also includes stipled ceiling, switch installation on dimmers and base/casing (whatever that is).

A. I think you need to get three or four estimates..all need to be written and describing exactly what is included. Write out what you want done to your space, so each contractor can bid accordingly. I have to tell you, I do not like working with friends (unless it is just for an afternoon having dinner or beer as pay). Do not make a decision until you have all the estimates. As for paying..that is a personal decision you need to make on your own or with your financial advisor from the bank. A word of advice..wiring should be done by a licensed electrician and do not cheap out on the recessed lighting.

(No Chosen Answer)